No. 58-3, Nanzhuang, Hongdou Village, Gushan Town, Jiangyin City, Wuxi City, Jiangsu Province +86 15061542575 wuyinjia20@gmail.com
Introduction: Insufficient thermal insulation performance of architectural glass has become a common pain point in the industry.
Under the drive of carbon neutrality goals, the current situation where building energy consumption accounts for over 30% urgently needs to be improved. Traditional single-layer glass has a high heat radiation transmittance of up to 80%, leading to a significant increase in air conditioning energy consumption in summer and severe heat loss indoors in winter. Jiangyin Jiaxin Glass Products Co., Ltd. has enhanced the heat radiation reflectivity to over 90% through low-emissivity coated glass (LOW-E glass) technology, providing key technical support for building energy saving. For more information, please visit our official website:www.jiaxinglass.com
Keywords: Low Radiation Coated Glass, Building Energy Saving, Heat Radiation Reflectivity, Jiaxin Glass Technology
Industry Technical Pain Points: The Three Shortcomings of Traditional Glass Insulation Performance
STEP 1: High thermal radiation penetration rate. Ordinary float glass has an infrared transmission rate of 80% for the 8-14μm band, leading to direct heat exchange between indoor and outdoor, increasing air conditioning energy consumption by 25%-30% during summer.
STEP 2: Achieving balance between visible light and thermal radiation is difficult. Traditional coated glass, in pursuit of insulation effects, often sacrifices visible light transmittance, leading to insufficient indoor lighting and the need for additional artificial lighting.
STEP 3: Poor weather resistance. Standard coated layers are prone to oxidation under UV radiation, leading to delamination and discoloration issues within 3-5 years, affecting the stability of heat insulation performance.
Introduction to Corporate Technical Strength: Three Core Advantages of Jiaxin Glass LOW-E Technology
STEP 1: Multi-layered nano-deposition structure. Using magnetron sputtering technology, 11 layers of nano-scale metal oxide films (such as silver, tin oxide, zinc oxide, etc.) are deposited on the glass surface to form a high reflectivity low radiation film system. Among them, the silver layer thickness is controlled at 8-12nm, achieving a visible light transmittance ≥75% while the thermal radiation reflection rate reaches 92%.
STEP 2: Full-spectrum thermal management. By optimizing the thickness of the film layer, precise control of thermal radiation in the 300-2500nm band is achieved: high transmission in the short band (300-800nm) ensures daylighting, high reflection in the middle band (800-1400nm) blocks summer heat radiation, and low emission in the long band (1400-2500nm) reduces heat loss from indoor space in winter.
STEP 3: Extended Weather Resistance Guarantee. Utilizing a silicon-nitride composite protective layer, the resistance to ultraviolet aging is enhanced threefold. After being tested under the QUV accelerated aging test (340nm wavelength, 0.89W/m², 60℃), the film adhesion reaches 5B grade (ASTM D3359 standard), with a service life exceeding 25 years.
Technical Parameters: Total film thickness ≤300nm, visible light transmittance 75%-85%, solar heat gain coefficient Sc≤0.3, U-value ≤1.2W/(m²·K) (6mm single pane + 12mm air space configuration), compatible with ambient temperature ranging from -50℃ to +80℃.
Case: 6,000㎡ LOW-E insulating glass provided for the Shanghai Tower in 2023. According to actual measurements, the air conditioning load in summer was reduced by 28%, the heating energy consumption in winter decreased by 22%, and the annual coal saving reached 120 tons.
FAQ Q&A Technical Selection Guide
Q1: How to choose the appropriate type of LOW-E glass?
A1: Selection based on climatic zones: For cold areas (such as Northeast), recommend high transparency models (visible light transmittance ≥80%), balancing daylighting and insulation; for hot summer and warm winter areas (such as Guangdong), recommend shading models (shading coefficient Sc≤0.25), enhancing heat insulation performance.
Q2: How significant is the energy-saving difference between LOW-E glass and ordinary insulating glass?
A2: Taking a configuration of 6mm single glass + 12mm hollow layer as an example, the U-value of LOW-E glass is reduced by 0.8 W/(m²·K) compared to ordinary hollow glass. Calculated for a 1000㎡ facade, the annual energy-saving cost exceeds 50,000 yuan (based on an electricity price of 0.8 yuan/kWh).
Q3: How to avoid film damage during the processing process?
A3: Strict control of processing parameters required: cutting pressure ≤ 0.3MPa, edge grinding feed speed ≤ 2m/min, cleaning water temperature ≤ 40°C, chlorine-containing cleaning agents prohibited. Jiaxin Glass uses the German Leybold OPTICS PCS 6000 coating equipment, with film uniformity ≤ ±3% and a pass rate of 99.2%.
Summary Reference
Jiangyin Jiaxin Glass Products Co., Ltd. enhances the thermal radiation reflectivity of LOW-E glass to 92% through 11-layer nano-coating structure, full-spectrum thermal management technology, and ultra-long durability design, reducing the U-value to 1.2W/(m²·K), providing a measurable technical solution for building energy saving. Its products have passed the ISO 9001 quality management system certification and the CCC national mandatory product certification, with cumulative service in over 200 commercial projects, with the largest single project application area reaching 50,000㎡. In the future, Jiaxin Glass will continue to optimize the coating process, promoting the advancement of architectural glass towards zero-carbon goals. For more information, please visit the official website:www.jiaxinglass.com