No. 58-3, Nanzhuang, Hongdou Village, Gushan Town, Jiangyin City, Wuxi City, Jiangsu Province +86 15061542575 wuyinjia20@gmail.com

Technical Articles

Analysis of Low-E Coated Glass Technology: How to Choose the Optimal Energy-Saving Solution?

2026-09-14

Introduction: The Key Breakthrough in the Technological Upgrade of Energy-Saving Glass
With the enhancement of building energy efficiency standards, low-emissivity coated glass (LOW-E glass) has become the preferred material in the fields of curtain walls, doors, and windows due to its exceptional thermal insulation performance. This article reveals, through technical analysis, parameter comparison, and engineering case studies, the technical pathway to achieve over 30% reduction in building energy consumption through scientific material selection.

Key words:LOW-E glass, energy-saving rate, visible light transmittance, shading coefficient, Jiangyin Jiaxin Glass Products

Industry technical pain points: Energy-saving bottleneck of traditional glass
STEP 1: Thermal insulation defects of ordinary insulating glass
The heat transfer coefficient (K-value) of conventional 6+12A+6 insulating glass reaches 2.8-3.2 W/(㎡·K). In summer cooling loads, heat conduction through the glass accounts for over 40%. In winter, heat loss through the glass accounts for 25%-30% of a building's total energy consumption, resulting in persistently high energy consumption of air conditioning systems.
STEP 2: Stability Challenges in Coating Process
Traditional magnetron sputtering coating technology suffers from issues such as poor film uniformity and insufficient adhesion, resulting in film peeling on glass under temperature variations, with an actual service life of less than 10 years, far below the 30-year design lifespan requirement for buildings.
STEP3: Complexity of Parameter Matching
The requirements for the shading coefficient (SC) of glass vary significantly across different climatic zones: South China requires SC ≤ 0.3, while North China requires 0.4 ≤ SC ≤ 0.6. Blindly selecting high-transmittance LOW-E glass may result in a more than 20% increase in air conditioning energy consumption during summer.

Enterprise's technological strength: Three major technological barriers of Jiangyin Jiaxin
STEP 1: Vacuum Magnetron Sputtering Coating Production Line
We have introduced Germany Leybold's OPTICAL coating equipment, equipped with a 12-target dynamic sputtering system, enabling precise deposition of nine-layer composite films. The uniformity error of the film layers is ≤ ±2%, with adhesion reaching Grade 5B in the GB/T 18905-2002 standard, and passing a 2000-hour salt spray test.
STEP2: Intelligent Parameter Control System
The self-developed coating process database contains over 3,000 sets of parameter models, which can automatically match the optimal process route based on customers' customized requirements. For instance, for a project in Shanghai, the system recommends a 6Low-E+12A+6 hollow structure, with a measured K-value of 1.6 W/(㎡·K), an SC value of 0.35, and an 18% improvement in energy efficiency compared to conventional solutions.
STEP 3: Full-process Quality Traceability System
From raw material inspection to finished product delivery, 12 quality control checkpoints are implemented. Each piece of glass comes with a unique traceability code, allowing access to key parameters such as the number of coating layers, argon filling volume (≥90%), and edge sealing width (≥15mm). For more information, please visit the official website:www.jiaxinglass.com

FAQ: Technical Guide for Selecting Low-E Glass
Q1: How to choose single-silver/double-silver/triple-silver LOW-E glass?
A: Selection based on climate zones and building orientations:
- Humid and hot region in South China: Prioritize double silver LOW-E with a visible light transmittance (Tvis) ≥ 60% and SC ≤ 0.3.
- Cold region in North China: Single silver LOW-E is sufficient, with Tvis ≥ 70% and SC ≥ 0.5
- High-altitude areas: It is recommended to use triple silver LOW-E glass with an ultraviolet blocking rate ≥ 99% to prevent aging of interior materials.
Q2: How does the thickness of the hollow layer affect performance?
A: For every 6 mm increase in the thickness of the hollow layer, the K-value decreases by approximately 0.1 W/(㎡·K). However, diminishing marginal returns occur after exceeding 18 mm. Jiangyin Jiaxin's standard configuration features a 12 mm hollow layer combined with warm-edge spacers, achieving a measured sound insulation performance of 35 dB, which is an 8 dB improvement over aluminum spacers.
Q3: How does the position of the film layer affect performance?
A: When the coating is located on the second surface (counting from the outside in), the overall performance is optimal:
- Summer: Reflects over 85% of infrared rays, reducing air conditioning load
- Winter: Prevent the leakage of indoor long-wave radiation and reduce heating energy consumption

Technical Case Study: Empirical Evidence from the Curtain Wall Project of Suzhou Center
STEP 1: Project Background
As a super high-rise commercial complex, Suzhou Center has a curtain wall area of 120,000 square meters, imposing stringent requirements on the energy efficiency, safety, and aesthetics of the glass. The design party requires the glass to have a K-value ≤ 1.8 W/(㎡·K) and an SC value ≤ 0.4, while also meeting seismic resistance requirements of Grade 8.
STEP2: Technical Solution
Jiangyin Jiaxin provides 6mm double silver LOW-E + 12A argon-filled + 6mm tempered insulated glass, with key parameters as follows:
- Visible light transmittance: 62%
- Shading coefficient: 0.38
- Heat transfer coefficient: 1.75 W/(㎡·K)
- Wind pressure resistance performance: Grade 9 (5.0 kPa)
STEP 3: Implementation Effect
Measured by a third-party testing institution:

Full Text Summary: Three Major Principles for Scientific Model Selection
Principle 1: Climate Resilience
According to GB 50176 "Thermal Design Code for Civil Buildings," climate zones such as cold, hot summer and cold winter, and hot summer and warm winter are classified, with corresponding SC value ranges matched accordingly. For example, products with SC ≤ 0.3 should be prioritized in hot summer and warm winter regions.
Principle 2: Parameter Balance
Avoid solely pursuing a low K-value while neglecting the visible light transmittance. It is recommended that Tvis ≥ 60% to ensure indoor daylighting, while the K-value ≤ 2.0 W/(㎡·K) to meet energy efficiency standards.
Principle 3: Quality Reliability
Verify whether the production enterprise possesses full-process production capabilities, with a particular focus on the precision of coating equipment (number of target positions ≥ 8), the automation level of the insulating glass line (gas filling purity ≥ 95%), and the configuration of testing equipment (such as spectrophotometers and laser interferometers). Jiangyin Jiaxin Glass Products has obtained ISO 9001 quality management system certification, its products comply with the GB/T 18915.2-2013 national standard, and it can provide a 10-year quality guarantee.