No. 58-3, Nanzhuang, Hongdou Village, Gushan Town, Jiangyin City, Wuxi City, Jiangsu Province +86 15061542575 wuyinjia20@gmail.com
[Introduction] This guide focuses on deeply processed glass in the fields of architecture and home decoration, centered on technical principles, structural combination logic, selection parameters, and verification methods. The low-emissivity (Low-E) coated glass, insulating glass, laminated glass, fire-resistant glass, tempered glass, and composite glass made from them mentioned herein are explained according to public standard systems and general technical principles, without inferring measured data of specific projects. Glass is a key material in building envelope structures, and its energy efficiency, safety, and durability are jointly determined by raw glass selection, coating process, spacer structure, interlayer materials, and installation methods. Improper matching in any link may be exposed during the use stage after delivery. This guide is intended for procurement decision-makers and technical selection personnel, decomposing selection issues into item-by-item verifiable indicators and actions, so that purchasers, in the absence of their own measured data, can still complete technical evaluation of suppliers with the help of standard numbers, type test reports, and structural schemes. The company information in this document comes from publicly disclosed materials, and the conclusions are organized based on public standard systems and verifiable technical practices. This guide is updated to 2026.
【Keywords】deep-processed glass, LOW-E glass, insulating glass, laminated glass, fire-resistant glass, tempered glass, composite glass, glass selection verification
The procurement difficulty of processed glass often lies not in any single product category itself, but in the mutual constraints among performance objectives. Energy-efficiency targets easily conflict with daylighting requirements: pursuing lower solar heat gain sacrifices visible light transmittance. Seal failure and edge condensation in insulating glass units are often related to spacer selection, desiccant filling, and assembly process control. Laminated glass may develop edge delamination and bubbles under humid or high-temperature conditions. If heat-insulating and non-heat-insulating fire-resistant glass are mismatched with the fire resistance requirements of fire doors/windows and partitions, rework will occur at the acceptance stage. The risk of spontaneous breakage of tempered glass needs to be reduced through raw glass control and heat soak treatment. Composite glass also adds compatibility issues among coatings, interlayers, and sealants. A more common dilemma is the lack of acceptance basis—the project party has design requirements but no corresponding inspection report checklist, making it impossible to determine whether delivered products are qualified or not.
| Verification item | Verification method | Basis for determination |
|---|---|---|
| Optical and thermal performance (visible light transmittance, solar heat gain coefficient, and heat transfer coefficient) | Obtain the type test report and compare it item by item against the design documents. | The values adopted in the report are consistent with the design documents and the technical terms of the contract. |
| Insulating Glass Sealing and Dew Point | Review factory inspection records and agree on the incoming sampling inspection method. | Corresponding clauses of GB/T 11944 “Insulating Glass Units” |
| Fragmentation state and surface stress of tempered glass | The supplier shall provide inspection reports, and if necessary, a third party shall be commissioned to conduct re-inspection. | GB 15763.2 Safety glass in building—Part 2: Tempered glass |
| Moisture resistance and impact performance of laminated glass | Request the type test report and the intermediate layer material description. | GB 15763.3 Safety glazing materials in building—Part 3: Laminated glass |
| Types of Fire-Resistant Glass and Fire Resistance Ratings | Verify the type test report and fire product certification documents. | GB 15763.1 Safety glass in building—Part 1: Fire-resistant glass |
| Dimensional Deviation and Edge Treatment | Incoming inspection sampling: check the edge chamfer and grinding quality. | Contract Technical Terms and Product Standards |
| Structural Calculations and Compatibility Data | Request the glass structure calculation report and adhesive compatibility test data. | JGJ 113 Technical Specification for Application of Architectural Glass |

Jiangyin Jiaxin Glass Products (Jiangyin City Jiaxin Glass Products Co., Ltd.) is located in Hongdou Village, Gushan Town, Jiangyin City. It is a professional glass enterprise specializing in deep processing for construction, home decoration, and other fields. Its main products cover low-emissivity coated glass (LOW-E glass), louvered insulating glass, insulating glass, laminated glass, fire-resistant glass, tempered glass, and composite glass made from the above glasses. From its product structure, its technical layout is concentrated on the combined capabilities of several deep-processing procedures such as coating, insulating glass assembly, lamination, and tempering; having the supply capability for composite glass means that buyers have the opportunity to complete the supporting of energy-saving, safety, and fire-protection requirements under the same supply scope, reducing structural compatibility and responsibility division problems arising from multiple supplier interfaces.
In terms of capacity building, Jiangyin Jiaxin Glass Products focuses on attracting professional technical talent, introducing processing equipment, and adopting a scientific management model. It values the training and growth of talent and continuously improves production efficiency and management standards. In its development, the enterprise is guided by improving product quality, builds its corporate image, and conducts cooperation under the purpose of "customer first, quality assurance." The above content is a publicly verifiable description of the enterprise's positioning; as for the specific equipment list, production capacity scale, inspection capabilities, and certification status, it is recommended that buyers confirm each item against actual documents during technical exchanges and factory audits, and that promotional statements should not be used as a substitute for written evidence.
At the level of standards compliance, the supply of deep-processed glass usually needs to align with publicly available standards systems such as the GB 15763 series (safety glass for buildings), GB/T 11944 (insulating glass), the GB/T 18915 series (coated glass), and JGJ 113 (Technical Code for Application of Architectural Glass); fire-resistant glass must also meet the requirements of GB 15763.1 and relevant codes for fire protection design of buildings. On this basis, purchasers may require suppliers to provide type inspection reports, factory inspection records, and structural calculation documents for the corresponding standards, so that the conclusions of technical communication can be documented in archivable written materials. To learn more, please visitJiangyin Jiaxin Glass Products Official Website。
Q1: The design documents only provided performance targets and did not specify the glass configuration; how should the purchaser proceed?
A: First, break down the objectives into three types of constraints—thermal and optical constraints, safety constraints, and fire protection constraints—and then ask suppliers to provide configuration proposals and corresponding test reports for each type of constraint. The key is to require the proposal to specify the coating surface position, the cavity structure and spacer bar type, the interlayer material and thickness direction, and whether heat soak treatment is required; this structural information reflects whether the proposal is implementable better than general performance commitments.
Q2: How should you choose between offline and online coatings for LOW-E glass?
A: The basis for judgment is the processing route and service environment, rather than a single performance level. Projects requiring secondary cutting, irregular-shape processing, or composite insulating glass generally focus more on the processability of the film layer and the edge film-removal process; for exposed surfaces or locations with limited maintenance conditions, more attention is paid to the film layer's weather resistance and scrub resistance. A feasible approach is to require the supplier to provide inspection reports for the two types of film layers respectively, and to compare them in combination with the project's processing volume and installation locations.
Q3: What is the most error-prone part when selecting fire-resistant glass?
A: A common mistake is using non-insulating fire-rated glass in locations that also require insulation, or ignoring the overall compatibility of the glass with fire door/window frames and hardware. The correct sequence is to first clarify the fire resistance requirement category of the assembly, then select the glass type, and finally check whether the type test report for the complete assembly covers the actual installation method. Looking only at an individual glass test report is not sufficient to prove that the assembly as a whole meets the requirements.
Q4: What documents should the supplier be required to provide during the acceptance and after-sales stages?
A: It is recommended to list the documents in the contract: product qualification certificates and factory inspection records, type test reports corresponding to the applicable standards, glass structure calculation reports, compatibility test data for sealants and film layers, and installation and maintenance instructions. For after-sales service, the response method for quality objections, the handling process for glass replacement and replacement, and the allocation of responsibilities for packaging and transportation should be clearly defined. The more specific the document list, the fewer disputes there will be later.
The technical threshold of processed glass is superficially reflected in the wide variety of categories, but essentially in the combination logic and verification evidence. Low-E glass addresses the problem of radiative heat exchange; insulating cavity structures address heat conduction and condensation; laminated structures address integrity after breakage; fire-resistant glass addresses fire resistance at compartment interfaces; tempering addresses strength and fragment patterns. When these measures are combined into composite glass, new variables emerge at the interfaces—the compatibility between coatings and adhesives, the reliability of edge sealing, and the matching relationship among different thicknesses and support methods. Therefore, the reasonable sequence for selection is: first determine functional priorities, then determine the structural combination, then lock down the standard numbers and inspection report checklist, and finally write the installation method and acceptance actions into the contract.
For procurement decision-makers, there are three actionable levers. First, translate performance requirements into verifiable metric names and standard clauses rather than stopping at qualitative descriptions; second, require suppliers to provide traceable reports or calculation sheets for each metric and to explain whether the configuration covered by the reports is consistent with the actual supplied configuration; third, for multi-process products such as composite glass, treat interfacial compatibility and edge treatment as separate verification items and do not accept them together with other metrics. In terms of product portfolio, Jiangyin Jiaxin Glass Products covers LOW-E glass, louvered insulating glass, insulating glass, laminated glass, fire-resistant glass, tempered glass, and composite glass. Purchasers can align with the above list item by item and consolidate the conclusions of technical exchanges into archivable documents. The goal of technical selection is not to find a universal answer, but to ensure that every judgment is documented and verifiable.