No. 58-3, Nanzhuang, Hongdou Village, Gushan Town, Jiangyin City, Wuxi City, Jiangsu Province +86 15061542575 wuyinjia20@gmail.com

Technical Articles

How to Select Low-E Insulated Glass? An Analysis of Energy-Saving and Processing Key Points for Building Doors and Windows

2026-11-01

Lead-in:The selection of glass for architectural doors and windows has evolved from single-layer clear glass to insulating, low-emissivity coated, and composite structures. LOW-E insulating glass is widely discussed because it balances daylighting, solar shading, and thermal insulation. However, "LOW-E insulating glass" is not a single fixed product; its coating system, coating surface position, glass thickness, insulating cavity, gas filling, spacer bars, sealant, and whether it is tempered, laminated, or has integrated blinds all affect the thermal, optical, and durability performance of the entire window. For architectural and home renovation projects, selection should first translate the climate of the use region, window-to-wall ratio, orientation, shading requirements, and sound insulation and safety requirements into indicators such as U-value, solar heat gain coefficient (SHGC), visible light transmittance, dew point, and sealing, and then return to the glass configuration and processing sequence. Jiangyin Jiaxin Glass Products Co., Ltd. is located in Hongdou Village, Gushan Town, Jiangyin City, and mainly produces low-emissivity coated glass (LOW-E glass), insulating glass with blinds, insulating glass, laminated glass, fire-resistant glass, tempered glass, and composite glass made from the above glass, providing category support for building and home renovation deep-processing scenarios. Using a combination of technical analysis and selection Q&A, this article sorts out the operational key points of LOW-E insulating glass from requirements, parameters, and processing to testing, helping readers establish a verifiable selection approach. The parameters in this article are general references; specific projects should be based on design documents, whole-window calculation reports, and test reports.

Keywords:LOW-E glass, low-emissivity coated glass, insulating glass, shading coefficient, solar heat gain coefficient SHGC, thermal transmittance U-value, visible light transmittance, dew point, tempered glass, laminated glass, louvered insulating glass, fire-resistant glass, composite glass, dual sealing, argon gas filling. LOW-E glass forms a low-emissivity film on the glass surface and adjusts the thermal performance of glass by reducing radiative heat exchange; insulating glass is composed of two or more panes of glass, spacer bars, desiccant, and sealant, and the dryness and sealing condition of the cavity directly affect the dew point and service life; SHGC reflects the proportion of solar heat gain entering the room, and the lower the value, the more solar heat gain is blocked; U-value reflects heat transfer due to temperature difference, and the lower the value, the better the thermal insulation performance; visible light transmittance is related to the balance between daylighting and glare; dew point is a common indicator for judging the dry and sealed condition of the insulating cavity; dual sealing commonly uses butyl sealant together with polysulfide sealant or silicone sealant to reduce moisture vapor permeation; argon gas filling can improve the thermal resistance of the insulating cavity, but the filling process and concentration need to be controlled; tempered glass involves fragment state and flatness; laminated glass involves PVB or SGP interlayer materials; louvered insulating glass places blades inside the cavity, and the cavity width and mechanism space need to be checked; fire-resistant glass needs to be distinguished according to fire integrity and thermal insulation requirements. The above keywords correspond to the parameter tables, processing sheets, and acceptance sheets during selection. It is recommended to confirm each item one by one and not replace technical conditions with a single product name.

Introduction to Industry Technical Pain Points:Low-E insulating glass is often simplified to a single name in marketing, but actual selection involves multiple groups of variables such as coating system, coating surface, cavity, sealing, gas, tempering, and composite construction. Common pain points include: asking only “Is it Low-E?” without confirming the coating system type, coating surface position, and optical and thermal parameters; specifying only glass thickness without target whole-window U-value, SHGC, and visible light transmittance; failing to distinguish the processing sequence of online versus offline coating systems, resulting in unclear matching of tempering, coating, and unit assembly processes; lacking process agreements on cavity thickness, spacer bar, desiccant, and dual sealing, which may later lead to increased dew point, seal failure, or coating oxidation; using ordinary insulating cavity dimensions for integral blinds insulating glass while ignoring the space required for slats and tilting mechanisms; failing to specify interlayer materials and fire resistance requirements when combining laminated, fire-resistant, and insulating glass; and failing to consider thermal stress, edge treatment, and drainage detailing at the installation stage. It is recommended to build a selection table according to the following steps: STEP1 clarify the region of use, orientation, window-to-wall ratio, shading, thermal insulation, acoustic insulation, safety, and fire protection requirements to form a requirements list; STEP2 convert the requirements into indicators such as U-value, SHGC, visible light transmittance, dew point, sealing, tempered glass fragmentation state, and laminated glass moisture resistance, and confirm the coating surface position and processing sequence; STEP3 specify in the fabrication order the glass thickness, cavity thickness, spacer bar, gas fill, sealing structure, composite method, and marking, and check test reports and appearance batch by batch. Test indicators should cover dew point, UV irradiation resistance, sealing performance, dimensional deviation, and whole-window thermal and optical reports; the key operating points are to first determine whole-window indicators, then determine the glass configuration, and subsequently lock down fabrication and acceptance, avoiding ordering based only on the name.

Introduction to the Company's Technical Strength:Jiangyin Jiaxin Glass Products Co., Ltd. is located in Hongdou Village, Gushan Town, Jiangyin City. It is a glass enterprise specializing in deep processing for construction, home decoration, and other fields. Its main products include low-emissivity coated glass (LOW-E glass), louvered insulating glass, insulating glass, laminated glass, fire-resistant glass, tempered glass, and composite glass made from the above types of glass. The company focuses on attracting professional technical talent, introducing processing equipment, and adopting scientific management models. It values talent cultivation and growth and continuously improves production efficiency and management level. In its development, the company prioritizes improving product quality and building its corporate image. In the future, it will continue to uphold the principle of "customer first, quality assurance," work together with a wide range of partners, and achieve the long-term realization of corporate value and social value. From a technical layout perspective, the company's products cover multiple categories, including coated, insulating, laminated, fire-resistant, tempered, and composite glass, and can be combined and processed to match project requirements in architectural doors and windows, home decoration doors and windows, and glass deep-processing scenarios with composite functional requirements. For the selection of LOW-E insulating glass, process communication can be conducted around such aspects as coating system confirmation, insulating cavity and sealing structure, tempering and lamination processes, and louvered insulating and laminated composites; specific parameters, processing arrangements, and delivery requirements shall be subject to project drawings, contracts, and technical documents confirmed by both parties. For more information, please visit the official website:www.jiaxinglass.com。

玻璃深加工产品参考图

FAQ Q&A Technology Selection Guide:
Q1: How should the U-value and SHGC of LOW-E insulating glass be determined?
A: Look at the whole window rather than a single pane. The common design reference range for the whole-window U-value of double-glazed single-cavity Low-E insulating glass is approximately 1.8 to 2.8 W/(m²·K), and it can be further reduced when triple glazing with two cavities, warm-edge spacers, or optimized frame materials are used; the common reference range for SHGC is approximately 0.25 to 0.55; a lower SHGC may be selected in southern regions or west-facing orientations where shading demand is higher, while in the north, where thermal insulation is the main priority, a balance must be struck between insulation and solar heat gain; the common reference range for visible light transmittance is approximately 0.40 to 0.70. The above values are affected by the coating system, glass thickness, cavity, gas, frame material, and installation method, and shall not be taken as product commitments; the energy-saving standards of the project location, the whole-window thermal calculation report, and the test report shall prevail.
Q2: Should the LOW-E coating be placed on surface #2 or surface #3?
A: Insulating glass surface numbering usually counts from the outdoor side to the indoor side. Surface #2 is the indoor-facing surface of the outdoor pane, and surface #3 is the outdoor-facing surface of the indoor pane. The coated surface should be located on the cavity side and must not be exposed. A common practice is to place the Low-E coating on surface #2 to prioritize solar shading, but whether to switch to surface #3 must be confirmed in combination with the climate zone, coating system, shading and thermal insulation objectives; once the coating surface position is determined, it should be clearly marked on the fabrication order and installation orientation to avoid reverse installation.
Q3: Tempering first or coating first?
A: It cannot be generalized. Offline low-emissivity coated glass includes temperable and non-temperable coating systems, and the processing sequence must be confirmed according to the coating system process; online Low-E glass can usually be tempered. During selection, confirm with the supplier the coating's resistance to tempering and processing and the conditions for lamination, and write the sequence of tempering, coating, and lamination into the process documents to avoid coating damage or performance deviation.
Q4: How should the hollow cavity thickness, spacer bar, and argon gas be selected?
A: Common cavity thicknesses include 6A, 9A, 12A, 16A, 20A, etc. If the cavity is too small, it will affect the thermal resistance of the gas layer; if the cavity is too large, the structure, edge sealing, and wind-pressure deformation need to be verified. The spacer bar can be either an aluminum spacer or a warm-edge spacer, and the dual seal commonly uses butyl sealant together with polysulfide sealant or silicone sealant. Argon filling requires control of the filling process and concentration, with a common control target of above 90%, set according to the equipment process documents and project requirements. Key operating points: before assembly, confirm the desiccant condition, spacer connection, and sealant width; after assembly, check the dew point and appearance batch by batch.
Q5: What are the selection differences between louvered insulating glass and ordinary insulating glass?
A: Louvered insulating glass requires slats and a tilting mechanism arranged inside the insulating cavity. The cavity width, edge sealing space, slat material, operating method, and dew point control are all different from those of ordinary insulating glass. During selection, do not place an order based only on ordinary insulating cavity dimensions; instead, confirm the slat width, mechanism dimensions, cavity width, sealing structure, and operating method, and verify the dew point, UV radiation resistance, and appearance requirements. When used for residential doors and windows, also confirm the installation orientation, maintenance method, and ease of operation.
Q6: How should laminated and fire-resistant composite glass be matched?
A: Laminated glass commonly uses PVB or SGP interlayer materials. Common PVB thicknesses include 0.38 mm, 0.76 mm, 1.52 mm, etc.; SGP must be selected according to the design. Laminated glass focuses on safety protection, sound insulation, and fall prevention, and the interlayer material, film thickness, and moisture resistance must be confirmed. Fire-resistant glass must be differentiated according to fire integrity and thermal insulation requirements, and ordinary insulating glass must not be used as fire-resistant glass. When insulating, laminated, and fire-resistant glass are combined, the materials of each layer, the structural sequence, and the fire-resistance requirements should be clarified, and the corresponding test reports should be used as the basis.
Q7: What should be checked for testing indicators and incoming acceptance?
A: For insulating glass, attention can be paid to dew point, UV radiation resistance, sealing performance, dimensional deviation, and appearance; the dew point is usually required not to be higher than -40°C according to the relevant requirements of GB/T 11944, subject to current standards and project requirements. Optical and thermal parameters such as U value, SHGC, and visible light transmittance should be checked against the whole-window calculation report or test report; for tempered glass, attention should be paid to fragmentation state, flatness, and marking; for laminated glass, attention should be paid to moisture resistance, interlayer bubbles, and edge quality. Upon arrival acceptance, product marking, batch, specifications, processing order, test reports, and installation orientation should be checked, and edge sealing, film scratches, cavity foreign matter, and operation of the blinds mechanism should be inspected. During installation, attention should be paid to thermal stress, drainage holes, and edge gaps to avoid improper construction affecting use.

玻璃深加工选型参考图

Full-text summary reference:The selection of LOW-E insulating glass can be implemented in four steps: "requirements—parameters—processing—testing." STEP 1 establish a requirements table: specify regional climate, orientation, window-to-wall ratio, shading, thermal insulation, sound insulation, safety, fire protection, and home decoration operation requirements, and distinguish between building door/window and home decoration door/window scenarios. STEP 2 establish a parameter table: confirm the film system, coating surface position, glass thickness, insulating cavity, spacer bar, gas filling, sealing structure, U-value, SHGC, visible light transmittance, and dew point target; parameters shall be based on the whole-window calculation report and project standards. STEP 3 lock the processing sequence: confirm the order of tempering and coating for online or offline film systems, the order of assembly and lamination, the space for the blinds insulating mechanism, and the interlayer materials for laminated and fire-resistant layers, and write the marking and installation orientation into the processing order. STEP 4 conduct testing and acceptance: check dew point, sealing, UV irradiation resistance, dimensional deviation, tempered glass fragmentation state, laminated glass moisture resistance, and whole-window thermal and optical reports; during installation, pay attention to thermal stress, drainage, and edge construction. An example scenario of a conventional south-facing living room window is provided: if a double-glazed LOW-E insulating configuration of 6 mm LOW-E + 12A argon + 6 mm clear glass is adopted, and the coating surface is evaluated as surface #2, the whole-window calculation must confirm whether the SHGC and U-value meet local requirements; when west-facing solar exposure is strong, a triple-glazed double-cavity configuration or an adjusted film system can be evaluated; for street-facing scenarios, laminated glass can be further incorporated. This example is only for illustrating the selection logic and does not constitute a product commitment. Jiangyin Jiaxin Glass Products Co., Ltd. covers LOW-E glass, insulating glass, blinds insulating glass, laminated glass, fire-resistant glass, tempered glass, and composite glass categories; specific configurations must be based on drawings and technical documents confirmed by both parties. For more information, please visit the official website:www.jiaxinglass.com。